24" Machinist Straight Edge, with 32 Straight & 16 Angled Feeler Gauges
- 상품가
- $45.99 (약 61,638원)
- 면세 한도
- $200 (목록통관) · 이하라 면세 예상
- 예상 합계
- 약 61,638원 + 배송비
가격 변동
기록 2일
기록된 2일 동안 가격 변동 없음
현재 61,638원
그래프 로딩 중…
아마존 달러 가격을 오늘 환율($1 = ₩1,340)로 환산해 표시합니다. 그날 환율 기준 금액은 그래프를 짚으면 보입니다.
⇄ 다른 상품과 가격 추이 비교한눈에 요약
24" Machinist Straight Edge의 가격은 10월 30일 기준 $45.99(약 61,638원)입니다. 가격 이력이 아직 짧아 역대 최저가와 비교한 판단은 보류합니다. 실시간 가격과 재고는 아마존에서 확인할 수 있습니다. 아마존 실시간 가격 확인 ↗
한국까지 예상 비용
- 상품가
- $45.99 (약 61,638원)
- 면세 한도
- $200 (목록통관) · 이하라 면세 예상
- 예상 합계
- 약 61,638원 + 배송비
- 국제 배송비는 아마존 결제 화면에서 확정돼요. 과세 대상이면 배송비에도 세금이 붙어 조금 늘어요.
- 미국에서 보내는 물건은 목록통관 $200, 식품·건강기능식품·의약품(일반통관)은 $150 이하면 면세예요.
- 같은 날 들어오는 여러 건은 합산해서 과세될 수 있어요.
- 세율은 분류별 대표값이고 환율은 오늘 환율 기준이에요. 정확한 세액은 관세청 예상세액 조회에서 확인하세요.
상품 특징
- Industrial & Scientific
- Test, Measure & Inspect
- Dimensional Measurement
- Image Unavailable Image not available forColor:
- Cylinder Head & Engine Block Must-Have Inspection Kit: after engine overheating or head gasket failure, cylinder head and engine block surfaces may cause hidden warpage that is not visible to the eye
- The Enhon engine inspection kit combines a precision straight edge with 32 straight and 16 angled feeler gauges to quickly check cylinder head and engine block flatness across multiple points, helping prevent gasket leaks and costly rebuild failure
- Straight Edge Tool with Feeler Gauges Set: the package includes - A 24" precision machinist straight edge crafted from thick cold rolled steel and featured a precision ground edge to +/- 0.001 inch for inspections
- A 32-blade straight feeler gauge (0.0015-0.035inch / 0.04-0.88mm) and a 16-blade offset feeler gauge (0.005-0.02inch / 0.127-0.508mm), providing both flatness reference and precise gap measurement in one system
- Complete Engine Rebuild Diagnostic Tool: first clean the cylinder head or engine block surface thoroughly, place the 24'' straight edge across multiple measuring positions (typically at least six points), insert the 0.0015in feeler gauge to check gaps between the cylinder head surface and straight edge, if approaching or exceeding tolerance 0.05 mm at most (unless the manufacturer specifies a different value) signal the need for resurfacing or machining
- Warm Tips for Best Accuracy: 1. always clean cylinder head & engine block surface thoroughly to avoid false readings
- 2. measure in multiple directions at least six points, and take multiple readings for consistent diagnosis
- 3. do not apply pressure on the straight edge during inspection as it may affect results
- 4. use the angled feeler gauge for tight or obstructed areas
- 5. gently insert the feeler gauge and store properly to maintain long-term precision and prevent deformation
- Professional Straight Edge and Feeler Gauge Combo: this machined straight edge with premium straight & angled feeler gauges is built for mechanics, engine builders, and precision repair, not only suitable for cylinder head and engine block, but also for fly wheels, main bearing saddles, cam bearing saddles, cam covers, bell housings, measuring precise gap widths in valves, spark plugs, piston rings and tight-fitting parts during maintenance or inspection
- Step 1 - Clean the surface thoroughly to avoid inaccurate readings.
- Step 2 - Place the 24'' straight edge across the surface in multiple directions including lengthwise, crosswise, and both diagonal directions at least 6 measurements.
- Step 3 - Insert the 0.0015in feeler gauge to check gaps between the cylinder head surface and straight edge (0.05 mm at most unless the manufacturer specifies a different value).
- Step 4 - If no gap is detected, the surface is considered flat and usable. If a small gap is present, verify against manufacturer tolerance. If a larger gap is detected, resurfacing or machining is recommended before engine reassembly.
- Complete Engine Rebuild Diagnostic Tool: first clean the cylinder head or