Bivethoi 7mm 홀 펀치 라운드 개스킷 펀치, 탄소강 할로우 홀 펀치 커터 도구 고무 홀 펀치, 벨트 패브릭 캔버스 종이 플라스틱 공예용 시계 밴드 가죽 홀 펀치 (미터법)

상품 특징

• 패키지 구성: 시계 밴드 홀 펀치 1개, 가죽 벨트 홀 펀치 직경: 7mm, 전체 길이: 3.54인치 / 90mm. 유형: 미터법.
• 메트릭 벨트 홀 펀치: 미터법 홀 펀치는 크기가 정확하며 홀 펀치 해머와 함께 사용하여 개스킷, 가죽 제품, 고무 제품 또는 비닐에 구멍을 빠르게 펀칭합니다.
• 다양한 용도: 스틸 가죽 홀 펀치는 장인, 시계 수리공, DIY 애호가에게 매우 적합하며 일상적인 작업 요구 사항과 창의적인 요구 사항을 충족하기 위해 구매하고 사용할 수 있습니다.
• 고품질 소재: 원형 홀 펀치 공구는 고품질 탄소강으로 만들어져 견고하고 내구성이 뛰어납니다. 수동 가죽 홀 펀처는 여러 겹의 원단을 쉽게 자를 수 있습니다.
• 안심하고 구매하세요: Bivethoi의 제품을 선택하게 되어 큰 영광입니다. 제품에 대해 궁금한 점이 있으시면 언제든지 저희에게 연락해 주십시오. 24시간 이내에 만족스러운 해결책을 제공해 드리겠습니다.
• 도구 및 주거 개선 중 #93,938위 (도구 및 주거 개선 에서 상위 100개 보기)
• writing on the bottles directly, or affixing adhesive labels was not going to work well.I thought about using an X-Acto knife to cut out the circles, but it would take a long time that way and I would get sloppy holes.This punch made the job easy. I printed alignment holes, slightly smaller than 20mm, on the label patterns. Looking through the side port of the punch, it was easy to see inside the punch and align it to the printed circle, which appears to be just slightly inside the cutting edge of the punch.I used a scrap of Masonite as a backing material, but could also have used any firm (bit NOT hard) expendable material such as some leather, etc.I found that a "double tap" with a hammer worked best. With one hand holding the punch firmly onto the label, an making sure that it was not tilted on edge, my other hand held a hammer. One light tap to make sure that I was going to hit the top end of the punch (and not my hand), a second strong blow to to the actual punching. I found that, while several lighter blows did work, the punch tended to bounce a tiny bit sideways after each blow, to I was punching holes that were slightly oval.The punched circle of material always ended up being inside the end of the punch, and it was quick and easy to dislodge it by poking my little finger through the punch's side port.I did measure the resulting punched holes, and they were spot-on 20mm, quite accurate.Since this is an inexpensive punch, and is made from carbon steel but apparently without being hardened, I can't speak for long this punch will last. If I were a professional or serious hobbyist who would do a lot of punching, I might wish to buy a more expensive punch(s), bit for occasional use I think this is a good product. One caveat, this steel is untreated. I presume that the sharply ground cutting edge will rust over time, and worse in a humid environment. I am thinking of buy a few more sizes of this, and keeping them all inside some kind of gasketed box with a desiccant pack inside to keep it dry.자세히 보기간단히 보기 P. Schmidt별 5개 중 5개Easily makes clean and accurate holes on paper, thin plastic, leather, felt, etc.2024년 12월 15일에 미국에서 리뷰됨크기: 20mm스타일: 수동 제어확인된 구매I bought this product, in the 20mm diameter size, as a means to punch a lot of holes in sheets of laser-printable plastic sheet, in order to make small flag labels for "flux/oiling bottles
• writing on the bottles directly, or affixing adhesive labels was not going to work well.I thought about using an X-Acto knife to cut out the circles, but it would take a long time that way and I would get sloppy holes.This punch made the job easy. I printed alignment holes, sl