Garosa 1PCS GT-24 디지털 무선 모듈 산업용 등급 2.4G NRF24L01+PA+LNA 모듈 1100M 장거리 트랜시버 모듈 (패치 마운팅)

지금은 역대 최고가에 가까워요

역대 최고가와 1% 차이. 평균보다 7% 비싸요. 지금 사는 건 추천하지 않아요.

$7.87 10,577원

10월 23일 기준 아마존 실시간 가격 확인 ↗

최저 $7.29 평균 $7.38 최고 $7.95

해외직접배송 · 관세·배송비 별도

역대 최고가 근처

마지막 변경 10월 23일 10,308원 → 10,577원 ▲3% · 7일 전보다 ▲8% · 30일 전보다 ▲8% · 47일 동안 4번 바뀜(가끔)

보통 가격 9,797원 현재 10,577원

그래프 로딩 중…

최저9,797원10/15 · 최저가 18일
평균9,913원
최고10,684원9/6
기록23일9/6~10/23

가격 변동 내역

가격이 바뀐 날(최근 순). 기록이 없는 기간도 함께 적었습니다.
날짜가격변화
10월 23일 10,577원 $7.87 ▲3%
10월 22일 10,308원 $7.67 ▲3%
10월 18일 10,039원 $7.47 ▲2%
기록 없음 9/25~9/27 (3일)
기록 없음 9/16~9/19 (4일)
전체 보기 (변동 4건)
기록 없음 9/11~9/14 (4일)
9월 9일 9,797원 $7.29 역대 최저 ▼8%
9월 6일 10,684원 $7.95 기록 시작

아마존 달러 가격을 오늘 환율($1 = ₩1,344)로 환산해 표시합니다. 그날 환율 기준 금액은 그래프를 짚으면 보입니다.

⇄ 다른 상품과 가격 추이 비교

한눈에 요약

Garosa 1PCS GT-24 디지털 무선 모듈 산업용 등급 2.4G의 가격은 10월 23일 기준 $7.87(약 10,577원)입니다. 추적 기간 역대 최저가는 $7.29(10월 15일), 평균은 $7.38로, 지금은 평균보다 7% 비쌉니다. 실시간 가격과 재고는 아마존에서 확인할 수 있습니다. 아마존 실시간 가격 확인 ↗

한국까지 예상 비용

상품가
$7.87 (약 10,577원)
면세 한도
$200 (목록통관) · 이하라 면세 예상
예상 합계
약 10,577원 + 배송비
배송비 넣어 다시 계산해 보기 →
  • 국제 배송비는 아마존 결제 화면에서 확정돼요. 과세 대상이면 배송비에도 세금이 붙어 조금 늘어요.
  • 미국에서 보내는 물건은 목록통관 $200, 식품·건강기능식품·의약품(일반통관)은 $150 이하면 면세예요.
  • 같은 날 들어오는 여러 건은 합산해서 과세될 수 있어요.
  • 세율은 분류별 대표값이고 환율은 오늘 환율 기준이에요. 정확한 세액은 관세청 예상세액 조회에서 확인하세요.

상품 특징

  • Computers & Accessories
  • Networking Products
  • Network Transceivers
  • Image Unavailable Image not available forColor:
  • The CE pin is connected to the LNA enable pin. When CE = 1, the LNA is turned on. When CE = 0, the LNA is turned off. This is identical to the transmit and receive modes of the nRF24L01. In other words, the user does not need to care about the of the LNA at all.
  • Support 51 STM8S STM32 and other microcontroller development boards. The purpose is to switch to receive mode immediately after sending the GT-24. If CE = 0, the LNA is turned off, which will adversely affect the receiving sensitivity.
  • The module is nRF24L01P + PA + LNA and its driving method is exactly the same as nRF24L01P. Users can operate according to the nRF24L01P chip manual.
  • The CE can be connected high for a long time, but the module must first be set to the POWER DOWN power-down mode when writing to the register. It is recommended to connect the CE to the IO port of the MCU. The IRQ can be disconnected and the interrupt status can be obtained using the SPI polling mode. However, it is recommended to use an external interrupt from the microcontroller.
  • The module's CE pin timing can reach the 10us mentioned in the nRF24L01P technical manual, but we recommend changing it to: SPI until CE goes high until the transmit interrupt is completed, then keep 1ms high time, then Lower the CE.